Home > Products > PDF Product Catalog
Multilayer Chip Ferrite Bead
  • GZ series of Multilayer Chip Ferrite Bead
    GZ series beads generate impedance from relatively low frequencies, therefore are effective in noise suppression in the wide frequency range from 30MHz to several hundred MHz.
  • SZ series of Multilayer Chip Ferrite Bead
    SZ series beads have sharp and high impedance characteristics and therefore can minimize attenuation of the signal waveform. Moreover various impedances are available to match signal frequency.
  • PZ series of Multilayer Chip Ferrite Bead
    PZ series beads can be used in large current circuits due to its low DC resistance and can match power lines to a maximum of 6A DC.
  • HZ series of Multilayer Chip Ferrite Bead
    HZ series beads are similar to GZ, SZ , PZ and UPZ series at frequencies below 100MHz, however at 1GHz the impedance is approx. 3 times larger. So HZ series beads are particularly effective in noise suppression of more than 500MHz.
  • HPZ series of Multilayer Chip Ferrite Bead
    HPZ series are similar to HZ series in impedance characteristics yet have lower DC resistance and larger current than HZ series.
  • UPZ series of Multilayer Chip Ferrite Bead
    UPZ series beads have smaller DC resistance and larger allowable current than PZ series and are applied in noise suppression for power lines or large current signal lines of electrical equipments.
  • GZ-C series of Multilayer Chip Ferrite Bead
    GZ-C series beads have smaller DC resistance and larger rate current than GZ series, which are applied in general signal lines and can be effective in noise suppression in a wide frequency range from 30MHz to several hundred MHz.
  • SZ-C series of Multilayer Chip Ferrite Bead
    SZ-C series beads have smaller DC resistance and larger rate current than SZ series, besides they have sharp and high impedance characteristics and therefore can minimize attenuation of the signal waveform.
3-Terminal Filter
  • MFL series of Chip 3-Terminal EMI Filter
    MFL series EMI filters combine inductor and capacitor into one chip by T type and PI type circuit with rapid attenuation characteristics and effective maintenance of waveform quality of digital signal.
Wire Wound Chip Common Mode Filter for Signal Line
  • SDCW-C series of Wire Wound Chip Common Mode Choke Coil for Signal Line
    SDCW-C series common mode chokes enable highly coupled coils with coating winding type construction, coated with resin at the back of magnetic core. It provides lower height than SDCW series, especially suitable for ultra-thin high-speed line. It can be applied to USB 2.0, LVDS lines and audio lines.
  • SDCW-S series of Wire Wound Chip Common Mode Choke Coil for Signal Line
    SDCW-S series common mode chokes enable highly coupled coils with winding type construction. It provides smaller size than SDCW series, therefore make it ideal for common mode noise attenuation in USB2.0, IEEE1394, HDMI, USB3.0, audio lines and other LVDS lines.
  • SDCW series of Wire Wound Chip Common Mode Choke Coil for Signal Line
    SDCW series common mode chokes enable highly coupled coils with winding type construction and therefore make it ideal for common mode noise attenuation in USB, IEEE1394, HDMI, audio lines and other LVDS lines.
  • SDCW-H series of Wire Wound Chip Common Mode Choke Coil for Signal Line
    SDCW-H series common mode choke coil enables highly coupled coils with winding type construction. It provides lower differential mode insertion loss at high frequency (above 3GHz), therefore can be used in higher speed differential signal lines than SDCW series such as HDMI, USB3.0, etc.
  • SDCW-U series of Wire Wound Chip Common Mode Choke Coil for Signal Line
    SDCW-U Series common mode choke coil enables highly coupled coils with winding type construction. Its cut-off frequency can be boosted to higher than 8 GHz to reduce the effects of noise on the signals and de-skew the differential signals.
Wire Wound Common Mode Choke Coil for Power Line
  • BPCF-3222&4228 series of Wire Wound Common Mode Choke Coil for Power Line
    BPCF4228 and BPCF3222 series common mode pin type filter is designed with nanocrystalline alloys core, so that it can apply additional control when there is EMI under low frequency. At the same volume compare with ferrite, much higher inductance value can be reached just for white appliance wirings which ferrite materials can’t get and higher current can be endured.
  • BSCF series of Wire Wound Common Mode Choke Coil for Power Line
    BSCF1309 series common mode SMD type filter is designed with 4 sub-series. The common noise below 100MHz can be restrained by some of them. The products are applied power line and endured high current.
  • BPCF1211 series of Wire Wound Common Mode Choke Coil for Power Line
    BPCF1211 series common mode pin type filter is designed with 4 sub-series. The common noise below 100MHz can be restrained by some of them. The products are applied power line and endured high current.
Multilayer Chip Common Mode Choke Coil
  • SDCM series of Multilayer Chip Common Mode Choke Coil
    SDCM series common mode choke coil with multilayer type construction can suppress common mode noise effectively and keep differential mode signal, therefore are widely used in high speed differential signal lines such as USB2.0, IEEE1394, and other LVDS lines.
  • SDCMA series of Multilayer Chip Common Mode Choke Coil
    SDCMA series with multilayer construction integrating two common mode choke coils can suppress common mode noise effectively and keep differential mode signal, therefore are widely used in high speed differential signal lines such as IEEE1394, and other LVDS lines.

CEATEC JAPAN 2011

Date: October 4th-8th, 2011

Location: 2-1, Nakase, Mihama-ku, Chiba-city, 261-0023 Japan

Booth: 6E35